Quality Inspection for Tft Lcd Display Lcd - 4.3 Inch COF Structure Touch Screen Model:DMG48270F043_02W (COF Series) – DWIN Detail:
Specification
Display
| Color | 262K colors |
| LCD Type | IPS-TFT-LCD, |
| Viewing Angle | Wide viewing angel, typical value of 85°/85°/85°/85°(L/R/U/D) |
| Active Area（A.A） | 95.04mm (W)×53.86mm (H) |
| Resolution | 480×272 |
| Backlight | LED |
| Brightness | DMG48270F043_02WN:250nit |
| DMG48270F043_02WTR: 200nit | |
| DMG48270F043_02WTC: 200nit | |
| DMG48270F043_02WTCZ01:200nit | |
| DMG48270F043_02WTCZ02:50nit |
Voltage & Current
| Power Voltage | 3.6~5.5V, typical value of 5V |
| Operation Current | VCC=5V, max backlight, 220mA |
| VCC=5V, backlight off, 100mA |
Interface
| User interface | 50Pin_0.5mm FPC |
| Baudrate | 3150~3225600bps |
| Output Voltage | Output 1; 3.0~3.3 V |
| Output 0; 0~0.3 V | |
| Input Voltage （RXD） | Input 1; 3.3V |
| Input 0; 0~0.5V | |
| Interface | UART2: TTL; |
| UART4: TTL;（ Only available after OS configuration） | |
| UART5: TTL;（Only available after OS configuration | |
| Data Format | UART2: N81; |
| UART4: N81/E81/O81/N82;4 modes (OS configuration) | |
| UART5: N81/E81/O81/N82;4 modes (OS configuration) |
External Interface
| Pin | Definition | I/O | Functional Description |
| 1 | +5V | I | Power supply, DC3.6-5.5V |
| 2 | +5V | I | |
| 3 | GND | GND | GND |
| 4 | GND | GND | |
| 5 | GND | GND | |
| 6 | AD7 | I | 5 input ADCs. 12-bit resolution in case of 3.3V power supply. 0-3.3V input voltage. Except for AD6, the rest data is sent to OS core via UART3 in real time with 16KHz sampling rate. AD1 and AD5 can be used in parallel, and AD3 and AD7 can be used in parallel, which equals to two 32KHz sampling AD. AD1, AD3, AD5, AD7 can be used in parallel, which equals to a 64KHz sampling AD; the data is summed 1024 times and then divided by 64 to obtain a 64Hz 16bit AD value by oversampling. |
| 7 | AD6 | I | |
| 8 | AD5 | I | |
| 9 | AD3 | I | |
| 10 | AD2 | I | |
| 11 | +3.3 | O | 3.3V output, maximum load of 150mA. |
| 12 | SPK | O | External MOSFET to drive buzzer or speaker. The external 10K resistor should be pulled down to the ground to ensure that power-on |
| 13 | SD_CD | I/O | SD/SDHC interface,The SD_CK connects a 22pF capacitor to GND near the SD card interface. |
| 14 | SD_CK | O | |
| 15 | SD_D3 | I/O | |
| 16 | SD_D2 | I/O | |
| 17 | SD_D1 | I/O | |
| 18 | SD_D0 | I/O | |
| 19 | PWM0 | O | 2 16-bit PWM output. The external 10K resistor should be pulled down to the ground to ensure that power-on is low level. The OS core can be controlled in real time via UART3 |
| 20 | PWM1 | O | |
| 21 | P3.3 | I/O | If using RX8130 or SD2058 I2C RTC to connect to both IOs, SCL should be connected to P3.2,and SDA connected to P3.3 in parallel with 10K resistor pull-up to 3.3V. |
| 22 | P3.2 | I/O | |
| 23 | P3.1/EX1 | I/O | It can be used as an external interrupt 1 input at the same time, and supports both low voltage level or trailing edge interrupt modes. |
| 24 | P3.0/EX0 | I/O | It can be used as an external interrupt 0 input at the same time, and supports both low voltage level or trailing edge interrupt modes. |
| 25 | P2.7 | I/O | IO interface |
| 26 | P2.6 | I/O | IO interface |
| 27 | P2.5 | I/O | IO interface |
| 28 | P2.4 | I/O | IO interface |
| 29 | P2.3 | I/O | IO interface |
| 30 | P2.2 | I/O | IO interface |
| 31 | P2.1 | I/O | IO interface |
| 32 | P2.0 | I/O | IO interface |
| 33 | P1.7 | I/O | IO interface |
| 34 | P1.6 | I/O | IO interface |
| 35 | P1.5 | I/O | IO interface |
| 36 | P1.4 | I/O | IO interface |
| 37 | P1.3 | I/O | IO interface |
| 38 | P1.2 | I/O | IO interface |
| 39 | P1.1 | I/O | IO interface |
| 40 | P1.0 | I/O | IO interface |
| 41 | UART4_TXD | O | UART4 |
| 42 | UART4_RXD | I | |
| 43 | UART5_TXD | O | UART5 |
| 44 | UART5_RXD | I | |
| 45 | P0.0 | I/O | IO interface |
| 46 | P0.1 | I/O | IO interface |
| 47 | CAN_TX | O | CAN interface |
| 48 | CAN_RX | I | |
| 49 | UART2_TXD | O | UART2(UART0 serial port of OS core) |
| 50 | UART2_RXD | I |
Application
Product detail pictures:
Related Product Guide:
It adheres on the tenet Honest, industrious, enterprising, innovative to acquire new solutions regularly. It regards shoppers, success as its very own success. Let us establish prosperous future hand in hand for Quality Inspection for Tft Lcd Display Lcd - 4.3 Inch COF Structure Touch Screen Model:DMG48270F043_02W (COF Series) – DWIN, The product will supply to all over the world, such as: America , Malta , Poland , Over the years, with high-quality products, first- class service, ultra-low prices we win thee trust and favor of customers. Nowadays our products sell all over the domestic and abroad. Thanks for the regular and new customers support. We provide high quality product and competitive price, welcome the regular and new customers cooperate with us!
By Caroline
from Hamburg
- 2017.01.28 18:53
These high-quality intelligent serial communication LCD's from DWIN China are extremely easy to implement into fancy graphic applications with the state of art features and electronics to function as a user interface for just about any graphic touch screen application.
By Delia Pesina
from Turkey
- 2017.12.19 11:10
