OEM manufacturer Hmi Tft Lcd Touch Display - 4.0 Inch Intelligent Display Model: DMG48480F040_01W(COF Series) – DWIN Detail:
Video
Specification
ASIC Information
T5L0 ASIC | T5L0 ASIC is a low-power, cost-effective, GUI and application highly integrated single-chip dual-core ASIC designed by DWIN Technology for small-size LCD and mass produced in 2020. |
Display
Color | 262K colors | ||
LCD Type | IPS-TFT-LCD | ||
Viewing Angle | Wide viewing angel, typical value of 85°/85°/85°/85°(L/R/U/D) | ||
Display Area(A.A) | 71.86mm (W)×70.18mm (H) | ||
Resolution | 480*480 | ||
Backlight | LED | ||
Brightness | DMG48480F040_01WN:260nit DMG48480F040_01WTC:230nit DMG48480F040_01WTCZ01:230nit DMG48480F040_01WTCZ02:65nit |
Touch parameters
Type | CTP (Capacitive Touch Panel) | ||
Structure | G+G structure | ||
Touch Mode | Support point touch and drag | ||
Surface Hardness | 6H | ||
Light Transmittance | Over 90% | ||
Life | Over 1,000,000 times touch |
Voltage & Current
Power Voltage | 4.5~5.5V, typical value of 5V | ||
Operation Current | 245mA, VCC=5V, max backlight | ||
75 mA, VCC=5V, backlight off |
Reliability Test
Working Temperature | -20~70℃ |
Storage Temperature | -30~85℃ |
Working Humidity | 10%~90%RH |
Interface
User interface | 50Pin_0.5mm FPC | ||
Baudrate | 3150~3225600bps | ||
Output Voltage | Output 1, Iout = 1mA;3.0~3.3 V | ||
Output 0, Iout =-1mA;0~0.3 V | |||
Input Voltage (RXD) |
Input 1, Iin = 1mA;0~3.3V | ||
Input 0, Iin = -1mA;0~0.5V | |||
Interface | UART2: TTL; UART4: TTL;( Only available after OS configuration) UART5: TTL;(Only available after OS configuration |
||
Data Format | UART2: N81; UART4: N81/E81/O81/N82;4 modes (OS configuration) UART5: N81/E81/O81/N82;4 modes (OS configuration) |
External Interface
Pin | Definition | I/O | Functional Description |
1 | 5V | I | Power supply, DC3.6-5.5V |
2 | 5V | I | |
3 | GND | GND | GND |
4 | GND | GND | |
5 | GND | GND | |
6 | AD7 | I | 5 input ADCs. 12-bit resolution in case of 3.3V power supply. 0-3.3V input voltage. Except for AD6, the rest data is sent to OS core via UART3 in real time with 16KHz sampling rate. AD1 and AD5 can be used in parallel, and AD3 and AD7 can be used in parallel, which equals to two 32KHz sampling AD. AD1, AD3, AD5, AD7 can be used in parallel, which equals to a 64KHz sampling AD; the data is summed 1024 times and then divided by 64 to obtain a 64Hz 16bit AD value by oversampling. |
7 | AD6 | I | |
8 | AD5 | I | |
9 | AD3 | I | |
10 | AD2 | I | |
11 | 3.3 | O | 3.3V output, maximum load of 150mA. |
12 | SPK | O | External MOSFET to drive buzzer or speaker. The external 10K resistor should be pulled down to the ground to ensure that power-on is low level. |
13 | SD_CD | I/O | SD/SDHC interface,The SD_CK connects a 22pF capacitor to GND near the SD card interface. |
14 | SD_CK | O | |
15 | SD_D3 | I/O | |
16 | SD_D2 | I/O | |
17 | SD_D1 | I/O | |
18 | SD_D0 | I/O | |
19 | PWM0 | O | 2 16-bit PWM output. The external 10K resistor should be pulled down to the ground to ensure that power-on is low level. The OS core can be controlled in real time via UART3 |
20 | PWM1 | O | |
21 | P3.3 | I/O | If using RX8130 or SD2058 I2C RTC to connect to both IOs, SCL should be connected to P3.2,and SDA connected to P3.3 in parallel with 10K resistor pull-up to 3.3V. |
22 | P3.2 | I/O | |
23 | P3.1/EX1 | I/O | It can be used as an external interrupt 1 input at the same time, and supports both low voltage level or trailing edge interrupt modes. |
24 | P3.0/EX0 | I/O | It can be used as an external interrupt 0 input at the same time, and supports both low voltage level or trailing edge interrupt modes |
25 | P2.7 | I/O | IO interface |
26 | P2.6 | I/O | IO interface |
27 | P2.5 | I/O | IO interface |
28 | P2.4 | I/O | IO interface |
29 | P2.3 | I/O | IO interface |
30 | P2.2 | I/O | IO interface |
31 | P2.1 | I/O | IO interface |
32 | P2.0 | I/O | IO interface |
33 | P1.7 | I/O | IO interface |
34 | P1.6 | I/O | IO interface |
35 | P1.5 | I/O | IO interface |
36 | P1.4 | I/O | IO interface |
37 | P1.3 | I/O | IO interface |
38 | P1.2 | I/O | IO interface |
39 | P1.1 | I/O | IO interface |
40 | P1.0 | I/O | IO interface |
41 | UART4_TXD | O | UART4 |
42 | UART4_RXD | I | |
43 | UART5_TXD | O | UART5 |
44 | UART5_RXD | I | |
45 | P0.0 | I/O | IO interface |
46 | P0.1 | I/O | IO interface |
47 | CAN_TX | O | CAN interface |
48 | CAN_RX | I | |
49 | UART2_TXD | O | UART2(UART0 serial port of OS core) |
50 | UART2_RXD | I |
Application
Product detail pictures:
Related Product Guide:
We also supply merchandise sourcing and flight consolidation companies. We now have our very own manufacturing facility and sourcing business. We could present you with almost every kind of product relevant to our solution array for OEM manufacturer Hmi Tft Lcd Touch Display - 4.0 Inch Intelligent Display Model: DMG48480F040_01W(COF Series) – DWIN, The product will supply to all over the world, such as: Marseille , Turkey , Nairobi , We believe in establishing healthy customer relationships and positive interaction for business. Close cooperation with our customers has helped us to create strong supply chains and reap benefits. Our products have gained us widespread acceptance and the satisfaction of our worldwide valued clients.
By Quyen Staten from Vietnam - 2017.11.20 15:58
Impressed with the clarity and vivid colors of my DWIN display. It's been a game-changer for my business presentations!
By Lena from Liverpool - 2017.01.28 19:59