Specification
| User interface | 8Pin_2.0mm socket for power supply and serial communication. Download rate(typical value): 12KByte/s |
| Flash | 32MBytes (2*16MBytes NOR Flash), can be used to store user UI files such as fonts, images, music, etc., with erase/write cycles >100,000 times |
| Expand Flash pads | Two expansion slots are available, supporting expansion of NOR Flash and NAND Flash. The maximum expansion for NOR Flash is up to 64Mbytes. When combining NOR Flash and NAND Flash, the maximum expansion is up to 48Mbytes (using one expansion slots) + 512Mbytes |
| RTC | Super-capacitor for power supply. Accuracy: ±20ppm@25℃. It can work normally for 7 days after power failure |
| Buzzer | 3V passive buzzer |
| Speaker interface | 2Pin_2.0mm socket, speaker interface |
| SD card slot | Supports downloading of all files (user UI files, CFG files, underlying kernel firmware), displays download statistics on the screen, downloadrate: 4Mb/s.When downloading files, the SD card needs to be formatted in FAT32 format,with a recommended allocation unit size of 4096 |
| Reserved module interface | Supports soldering of WI-FI module and USB download module. WI-FI module model: WI-FI-10; USB module models: HDL702, HDL703 |
| PGT05 interface | Used for reprogramming the underlying DGUS firmware |
| LCD Type | IPS process TFT display screen |
| Viewing Angle | Wide viewing angle (typical values are 85°/85°/85°/85°), high contrast, and good color reproduction |
| Resolution | 1920×1080 pixels (0°/90°/180°/270°) |
| Color | 16.7M color (24-bit 8R8G8B) |
| Active Area (A.A.) | 343.16mm (W)×192.60mm (H) |
| Interface | eDP |
| Backlight Mode | LED |
| Backlight Service Life | >20000 hours (Time of the brightness decaying to 50%on the condition of continuous working with the maximum brightness) |
| Brightness | DMG19108K156_05WTC: 200nit |
| Brightness Control | 0~100 grade (When the brightness is adjusted to 1%~30%of the maximum brightness, flickering may occur and is not recommended to use in this range) |
| Note: You can use dynamic screen saver wallpapers to avoid afterimages caused by fixed page display for a long time. | |
| Type | CTP (Capacitive touch panel) |
| Interface | I²C |
| Structure | The G+FF/G+G structure is compatible, and the surface cover is tempered glass |
| Touch Mode | Single point touch and support continuous sliding touch |
| Surface Hardness | ≥6H |
| Light Transmittance | >85% |
| Life | >20,000H |
| Mode | UART2: RS232 UART4: RS232（ Only available after OS configuration) UART5: RS485（ Only available after OS configuration) |
|||||
| UART2,4 Voltage Level |
Test Condition | Min | Typ | Max | Unit | |
| Output 1 | 2.5 | 5.0 | - | V | ||
| Output 0 | - | -5.0 | -2.5 | V | ||
| Input 1 | -15.0 | -5.0 | - | V | ||
| Input 0 | - | 5.0 | 15.0 | V | ||
| UART2,4 Baud Rate |
3150~3225600bps, typical value of 115200bps | |||||
| UART5 Voltage Level |
Test Condition | Min | Typ | Max | Unit | |
| Output 1 | 2.5 | 5.0 | - | V | ||
| Output 0 | - | -5.0 | -2.5 | V | ||
| Input 1 | 0 | 2.5 | - | V | ||
| Input 0 | - | -2.5 | -0.2 | V | ||
| UART5 Baud Rate |
3150~921600bps, typical value of 115200bps | |||||
| Data Format | UART2: N81 UART4: N81/E81/O81/N82 ,4 modes (OS configuration) UART5: N81/E81/O81/N82 ,4 modes (OS configuration) |
|||||
| Interface Cable | 8Pin_2.0mm (RS232) 2Pin_2.0mm (RS485) |
|||||
| Rated Power | <8W | |||||
| Operating Voltage | 12~36V, typical value of 12V | |||||
| Operating Current | 620mA | VCC=12V, max backlight | ||||
| 180mA | VCC=12V, backlight off | |||||
| Recommended power supply: 12V 1A DC | ||||||
| Operating Temperature | -10℃~60℃ (12V @ 60% RH) | |||||
| Storage Temperature | -20℃~60℃ | |||||
| Conformal Coating | Yes | |||||
| Operating Humidity | 10%~90%RH, typical value of 60% RH | |||||
| Aging Test | 72 hours high temperature charged aging | |||||
